I assume you also tried a different cable?
Next thing I would try is a factory reset. If that doesn't resolve it, then it may be a hardware issue with the console.
I assume you also tried a different cable?
Next thing I would try is a factory reset. If that doesn't resolve it, then it may be a hardware issue with the console.
I am theorizing here, so don't take this as gospel. But my guess is that any "attribute definitions" information within the fixture profile is not necessarily a reliable indicator of the actual information in the patch of any given show file - especially in regards to FeatureGroups. I think that information is mostly used in case the attribute doesn't already exist in the show file into which you have imported that fixture type, so that the software knows where to add it. But if that attribute already exists in the show file, then the fixture will use the existing attribute definition rather than creating a new one, even if that particular fixture type wanted the attribute to be e.g. in a different Feature(Group).
https://support.actentertainment.com/knowledgeBase/34108761
(Look at the very end of the article)
You say Sequence 1 is "assigned" to Sequence 11 and 21. Meaning, you created Sequence 1, then Assigned it to Sequence 11 and 21? If so, then this is 100% expected, because all 3 sequences share the same cue data (and recipes are cue data - well, technically cue part data). If you actually wanted them to be separate data, then you would need to Copy Sequence 1 to Sequence 11 and 21 instead.
Regarding the second behavior you're describing of the programmer using that timing, this is expected based on the current ruleset, which is that activating one layer pulls all of the other non-default layers into the programmer as well (e.g. activating the absolute layer by choosing a preset in the programmer will pull the fade and delay layers into the programmer as well if they are not at default). You could enable Program Time at 0s if you didn't want to see this timing in the programmer.
Upgrading to a console is about 1-2 orders of magnitude in cost ($2k onPC to $60-100k console) and is, hardware-wise, a downgrade if you don't need physical faders and such.
Note that the least expensive 'console' model is the RPU - especially if you don't need physical faders. Still way more than a single onPC node, but a lot less than $60k.
Could perhaps be coming soon...
Use the [-] (minus) key before a FID/CID to deselect that fixture, the same way you would use the [+] (plus) key before an FID/CID to add it to your selection.
You're talking about interacting with a visualizer (rather than real DMX output), correct?
Assuming so, then I would guess that either you have the viz-key paired with onPC rather than with the visualizer, or you have the visualizer listening to sACN or Art-Net rather than using the MA-Net stream.
Instead of the '@' symbol at the end of a macro line, in MA3 just disable the 'Execute' cell for that macro line.
That being said, for something like selecting just the 5th instance, you could also do do this directly: 'Fixture x Thru y.5'
You can also use the [Pause] key on your keyboard to lock/unlock.
And you can also use the touch-pattern to unlock (or click with a mouse if you don't have a touchscreen): upper left, lower right, upper right, lower left
Can you clarify what you're hoping to do with that information?
dherderich it's the dot2 forum
Clintos FYI, something I myself run into every so often is that I forget that when you execute "List" it only lists properties that are common to all of the listed items, so if you are listing multiple items that have unique properties you won't see any of those properties listed. Whereas if you list them all individually one-at-a-time you'll see the properties as expected. (Hence in Dominik's screenshot where executing "List 8" shows the properties but just executing "List" wouldn't.)
Enable the TC setting {Ignore Follow}
Selkirk Creative what you want is:
not in front of console so bit of guess work, but have a try with "offcue".
In MA3 is no need for @....check the checkboxes in the software, you wanna write it to Command Line and not execute....but also in MA3 you should set the offtime into the offcue.
This is the dot2 forum, not the MA3 forum.