Posts by Thierry

Hello
MA2 and MA3 received updated software... what about DOT 2 ?

the same

Attention...
IP address starting with 2 or 10 are class A and not C .
Artnet works with A class such as 2.x.y.z or 10.x.y.z and the mask MUST be 255.0.0.0
If you use the mask 255.255.255.0, it's a C class as we use at home for IP dress like 192.168.1.x

C mask with a A IP adress could work only if you use the same 3 fist number ! but it's not the good way to configure a artnet node.
So : your PC mus have an IP adress like 2.100.0.2 with mask: 255.0.0.0
Your node must have an IP address like 2.150.17.13 with mask: 255.0.0.0

Be careful that you must have to choose the universe 00 (with subnet 00) for Artnet configuration, to run with Universe 1 for DMX software...

did you try with the IP adresse starting with 2 ? as i remember, the dot 2 in artnet mode a the adresse in 2.x.x.x

This morning, it works... so...

Hello
I need to download the stick maker and... the software download part of the website is empty !!!!!
...

We don't see the first word of a new update for a very long time. I expected to have news after the last exhibition but i think every thong is done for the MA3... Is it possible to have some news?

The problem with LED fixtures is that it's very difficult to dim them with very low values. Only some expensive fixture can be dimmed at a very little value. Most of them start with an important brightness

If you edit the cue you can set the "color fade" to 0

" It is also about managing distant fixture from the console (for example: adressing fixtures, changing fixture mode, etc...)."

That is the main purpose of RDM and one of the last development about dmx. Every new great fixture come to the market with RDM abilities and i can't imagine that MA lighting wouldn't add RDM functions to the DOT2!

hello
On your stick, do you have a "shows" folder ?
All your gz files must be in this folder (as a library folder for your fixtures...)
Your show file is labeled as "myName.show.gz"

hey
i think, because the fixture 3 is not in cue 2, the copy will leave the fixture 3 at full.
If you want an exact copy, goto cue 2 and try MA + STORE at cue 4 (store view)

you can try "thru thru at 0"

perfect
Thanks a lot

thanks
i already use this macro but the XML file has all the chanel values for all the cues... and il only need the cue names and would like a better way than copy it with a pen

Hello, my question is in the subjects Is it possible to export on my the cue mist in each executor (it would be great to write a rider).
Thanks

i think, don't forget to do a CLR CLR between the 2 STORE EXEC ?

Hello, je ne suis pas certain de pouvoir t'aider car je n'utilise pas dor2onPC mais la console elle-même, en Artnet sans passer par un routeur mais voilà quelques éléments et pistes de recherche.

La norme Artnet veut qu'on travaille dans un réseau de classe A : 10.x.x.x ou 2.x.x.x.
Par ailleurs l'adresse IP de module Enttec en 169.254.x.x signifie qu'il n'a pas reçu d'adresse IP par ton routeur... serveur DHCP bridé ?

Si tu travailles avec le routeur de ton installation perso, il faut vérifier si le service DHCP est installé. En principe il est sur une adresse de type 192.168.x.x (classe C). D'autre part, il faut regarder si tu ne peux pas configurer manuellement l'adresse IP du module (logiciel NMU téléchargeable sur le site d'ENTECC).

Si tu connectes directement le boitier via un cable Ethernet sur ton PC sans passer par un routeur, il est sans doute normal d'avoir des conflits d'adresse car ton PC n'est pas serveur DHCP. Il faut dans ce cas configurer les deux (PC et boitier) manuellement dans le même réseau : 10.0.0.13 pour ton PC (masque 255.0.0.0) et par exemple 10.0.0.14 pour le boitier (masque 255.0.0.0)

Le mieux serait d'avoir un point d'accès réservé à l'application lumière configuré en réseau de classe A.

also useful in theatre when you don't want the beam to goto the back curtain

at the moment ??????
may i expect something in few days... month...