Hello. What's mean "DMX input - this DMX input is currently only used for DMX remote control"?
Can i for example, save the DMX values of this input in cues? I would simply rewrite the older performances for the new console.
DMX in in MA dot2
BECOME PART OF THE COMMUNITY - Sign up here
-
-
Hi nasula,
as you already mentioned DMX Input in the dot2 means only DMX remote control.
The dot2 doesn´t support DMX merge for a special universe.Cheers
-
Hello Kanne. Thanks for your reply.
And is expected in the future? -
Hi nasula,
this is hard to say.
By now it is not expected. -
Well, too bad, we are left to wait and hope.
Cheers Kanne
Many good events -
can we explain this remote dmx control feature as i have dmxking box that has the additional in/out port that im not using..
maybe i can use quickshow laser dmx out to trigger dot2 which is reverse of what im currently doing
thanks
-
Please have a look at the manual: http://help2.malighting.com/To…d4-4f27-8381-8defa74eec66
Attention (!!) so far DMX Input is only possible via the local DMX In on a console! (v1.2.2.8)
Cheers,
Lars -
So it looks like I can use the MADRIX PLEXUS on dot2 console?
-
You can use everything which sends out one universe DMX512-A - for remote purpose!
-
Hello Lars.
I have a question. Is onPC the DMX entry to the ninth universe is active? Can I use this input to control the program using a DMX-to-Art-Net converter plugged into my laptop? -
Hi nasula!
Actually not, but one of the key features of the upcoming release is "DMX In via network".
So with the next version you are able to remote your onPC via DMX.Cheers,
Lars -
Cool. This is good news. Have fun after P & S ... Although we do not give a little rest ...
-
Hi nasula!
Actually not, but one of the key features of the upcoming release is "DMX In via network".
So with the next version you are able to remote your onPC via DMX.Cheers,
LarsHi folks,
as ArtNet input has been released and I'm left without the console I need for tomorrow... is the input active for onPC as well, with no HW attached to it?
Thanks and regards,
Luca -
Hi Luca,
yes this works!
I've tested it here and found a minor issue...it could be that you have to switch Art-Net Off and On again, if it doesn't work immediately. sACN works without any problems!
Cheers,
Lars -
having problems not getting art-net address shows 0.0.0.0. and enabled ??
-
Maybe it will help ...
External Content youtu.beContent embedded from external sources will not be displayed without your consent.Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy. -
omg ... have been watching that today on loop while setting up my router.. . have sCAN working like a charm.. appears that 00.0.0. is the correct artnet for the free universe but geting bomac to find anything is where im stuck
Lots of info in that video btw
-
Excuse me. I was just thinking about where the network settings are. On YT is a lot of other movies (by A.C.T I recommend), not just to dot2. I was leaning on the first settings, in the movie about art-net + freestyler. It helped me. Try this - Setup - Sessions - Stop/leave sessions - Start new or join an existing session. And what is your converter?
-
tryn to bet bomac to work...with bomes software and only dmxking pro2 interface.. might need another interface for bomac.. i dunno
seen excision with the paradox stage.. controlled with dot2 yesterday
not me
-
found the work around.. no bomac needed!
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!