Problem with software version 1.2

Lumirt · Apr 7th 2016

Hi all,
I have a problem with which I need advice. I have dot2 XL-B associated with dot2 Node4
After updating console to version 1.2 is at Node4 output D is set as the input. Can I change him alone DMX IN 1-8 but always as an input. I need it to be output. The manual is not written that the connector can be used as an input, it is a new feature or a bug?
Sorry for my English, more attached photo.
I wish you all a nice day and health Frankfurt
Lumirt

Push · Apr 7th 2016

Have you tries to switch off the node power, or to start the session new?
I can configure my nodes only from 1 to 8 (there is no “in” possible)…..

Go-Button · Apr 7th 2016

Assignable Ports is a new function in version 1.2.
I haven't worked with the node in the new version but I would try to right click in the XLR D settings and see if the console gives you a popup to choose port functions.

Lumirt · Apr 7th 2016

To Push: Yes, I made the restart several times, also a new session, I recorded another showfile still the same result.
To Go-Button: it means that I have to connect a mouse to the console? Another way to change this is? I try this evening.
You can use XLR DMX-D as input and will operate as DMX input on the console?

Go-Button · Apr 7th 2016

No mouse is not necessary. Just try to press the right encoder when the selection is in the right place.

Push · Apr 7th 2016

No idea how that could automatically adjust.
You can change this over the commandline.
Open a commandline and write:
cd netconfig (Please)
cd “DMX Node” (Please)
cd 1 (Please) (for your first node or 2 for your second node…)
assign 1 /XLRD=“out 4” (Please) (for the XLR “D” for Universe 4)
cd / (Please) (to go back to the root)

regards

Lumirt · Apr 7th 2016

to Go-Button: This is what I've tried. A new window opens where I assign a universe.
to Push: I try this evening.

Go-Button · Apr 7th 2016

So you solved it?

Lumirt · Apr 7th 2016

Now I'm at work, and the console is home, try to hints the evening. Write result immediately after testing

Lumirt · Apr 7th 2016

Hi all,
To Go-Button: im sorry, no effect, problem persist.
To Push: all done without errors, XLRD still the same, no effect. XLRB="out 4" Node setting port B to univers 4, this is ok. My Node4 is defective?
Any other ideas for solution ?

Go-Button · Apr 9th 2016

@Lumirt

You are right. After Update to 1.2. the node has Input 9 on XLR D.
I wasn't able to figure it out with command line right now but will try tonight again.

Michael · Apr 11th 2016

Hello guys,

this Problem occurs, when a Version 1.1 showfile is loaded into a console running 1.2 Software
and a dot2 node4 is in session.

Please have a look into the attched tech. Bulletin to solve this issue.
Sorry for this.

Cheers,
Michael

Lumirt · Apr 12th 2016

Hello,
thank you for a quick solution.
I dare little clarification.
assign 1 /XLRD=“out 4” command not properly, helped to command assign 1 /XLRD=“Out 4”
I had to use a capital letter O in a command out. although I have repeatedly tried other XLR then capital letter was not necessary.
Can anyone confirm this?

have a nice day
I'm sorry for my bad English

Michael · Apr 12th 2016

Hello Lumirt,
you are right -my mistake. The O of "Out" has to be an "O" not an "o"

Oh oh!
The tech. Bulletin has been corrected.
Thank you for finding this!

Cheers,
Michael

Problem with software version 1.2

Participate now!

Share

Tags